Datalogic-scanning MAGELLAN 8500 Bedienungsanleitung

Magellan® 8500/8500ΩProduct Reference Guide

8 Magellan® 8500 ScannerRSS-14 Label ID ...6-172RSS

5-12 Magellan® 8500 ScannerDecreasing-Load TestThis test ensures that the scanner/scale responds properly when a heavy object is followed by a signifi

Product Reference Guide 5-13Calibration Verification (Kilograms)Once you have completed the calibration sequence, you may be required to perform thes

5-14 Magellan® 8500 Scanner9. Increase the weight on the scale to 7.50 kg on the center of the weighing surface and check that the display reads betwe

Product Reference Guide 5-15Figure 5-4. European Shift Test (Metric)Increasing- Load Test (Phase 2)After completing the Shift Test, you must complete

5-16 Magellan® 8500 Scanner3. Place an additional 2.50 kilograms in the center of the weighing surface and check that the display reads between 14.990

Product Reference Guide 5-17Decreasing-Load TestThis test ensures that the scanner/scale responds properly when a heavy object is followed by a signi

5-18 Magellan® 8500 ScannerNOTES

Product Reference Guide 6-1Section 6ProgrammingIntroduction to Label ProgrammingThe programming bar code labels contained in this manual will allow y

6-2 Magellan® 8500 ScannerOnce you know the scanner’s current settings, you can determine what changes will be required to allow communication with yo

Product Reference Guide 6-3If you experience difficulties, have questions or require additional infor-mation, contact your local distributor, or call

Product Reference Guide 9Code 128 Fixed Length 2 ... 6-209Code 12

6-4 Magellan® 8500 ScannerWhat Is Programming Mode?Programming Mode is a state in which the scanner must be placed in order to accept commands via pro

Product Reference Guide 6-5Programming SessionA typical programming session is conducted as follows:1. Scan the SWITCH bar code to place the scanner

6-6 Magellan® 8500 Scanner3. Scan the SWITCH bar code to save any new settings and exit Programming Mode. The scanner will sound a beep and reset upon

Product Reference Guide 6-7Programming SequenceTo modify a scanner feature (item), the programming bar codes contained in this manual must be scanned

6-8 Magellan® 8500 ScannerTable 6-1. Programming Sequence11CAB23123456SETSWITCHENABLENEW FEATUREENABLE NEWFEATUREUSING THEFOLLOWINGSETTINGS...SWITCHSW

Product Reference Guide 6-9LED and Beeper IndicatorsThe scanner provides a set of indicators that verify/announce the various scanner functions. If Y

6-10 Magellan® 8500 ScannerTest ModeUse this feature to place the scanner into a testing, or “demo” mode. This special mode disables the scanner inter

Product Reference Guide 6-11General Scanner and Scale FeaturesDouble Read TimeoutThe Double Read Timeout feature sets a time limit that determines ho

6-12 Magellan® 8500 ScannerDouble Read Timeout — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the scanne

Product Reference Guide 6-13Laser TimeoutThe laser timeout feature sets the time for switching the visible laser diodes (VLDs) off if the scanner is

10 Magellan® 8500 ScannerCode 93 Fixed Length 2 ...6-247Code 93

6-14 Magellan® 8500 ScannerLaser Timeout — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the scanner read

Product Reference Guide 6-15Motor TimeoutThe Motor Timeout feature sets the time for automatically switching the motor off when the scanner is not in

6-16 Magellan® 8500 ScannerMotor Timeout — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the scanner read

Product Reference Guide 6-17Motor Timeout — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the scanner re

6-18 Magellan® 8500 ScannerGreen LED Idle StateThis feature specifies the state of the green scanner LED when the scanner is idle and ready to read a

Product Reference Guide 6-19Scanner Button OptionsConfigure the scanner volume button to one of the following modes of operation:• Enable all functio

6-20 Magellan® 8500 ScannerScanner Button Options — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the sca

Product Reference Guide 6-21Power-up Beep ControlSpecifies the type of audible indication that is made when entering scan-ner-active mode on power-up

6-22 Magellan® 8500 ScannerPower-up Beep Control — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the scan

Product Reference Guide 6-23Good Read Beep ControlThis feature enables/disables scanner beep upon successfully decoding of a label.To set this featur

Product Reference Guide 11EAN-8 ... F-5

6-24 Magellan® 8500 ScannerGood Read Beep FrequencyAdjusts the scanner’s good read beep to sound at low, medium, or high fre-quency (controls the beep

Product Reference Guide 6-25Good Read Beep Frequency — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the

6-26 Magellan® 8500 ScannerGood Read Beep LengthSpecifies the duration of a good read beep.To set the good read beep length:1. Scan the SWITCH bar cod

Product Reference Guide 6-27Good Read Beep VolumeSelects the beeper volume upon a good read beep. There are five selectable volumes, with each volume

6-28 Magellan® 8500 ScannerGood Read Beep Volume — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the scan

Product Reference Guide 6-29Good Read Beep Volume — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the sc

6-30 Magellan® 8500 ScannerGood Read When to IndicateThis feature specifies when the scanner will provide indication (beep and/or flash its green LED)

Product Reference Guide 6-31Good Read When to Indicate — continuedRemember to cover any unused bar codes on this and the facing page to ensure that t

6-32 Magellan® 8500 ScannerScale EnableUse this feature to enable or disable scale operation.To set this feature:1. Scan the SWITCH bar code.2. Scan y

Product Reference Guide 6-33Scale Country ModeWhen a weight is presented, the scanner/scale will apply the country-spe-cific weighing rules specified

12 Magellan® 8500 Scanner

6-34 Magellan® 8500 ScannerScale Country Mode — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the scanner

Product Reference Guide 6-35Scale Enforced Zero ReturnThis feature enables/disables the enforced zero return of the scale. Three settings are availab

6-36 Magellan® 8500 ScannerScale Enforced Zero Return — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the

Product Reference Guide 6-37Scale Automatic ZeroingThis feature enables/disables automatic zeroing of the scale if it goes under zero. If an under-ze

6-38 Magellan® 8500 ScannerScale Interface TypeUse this feature to select the scale interface type for RS-232 Standard and RS-232 Wincor/Nixdorf POS i

Product Reference Guide 6-39Scale Interface Type — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the sca

6-40 Magellan® 8500 ScannerScale Motion Level FilterIn environments where checkstands generate excessive vibration, the scale can be set to filter a c

Product Reference Guide 6-41Scale Motion Level Filter — continuedRemember to cover any unused bar codes on this and the facing page to ensure that th

6-42 Magellan® 8500 ScannerScale LED EnableThis feature enables/disables Scale LED (Yellow LED) operation.To set this feature:1. Scan the SWITCH bar c

Product Reference Guide 6-43Remote Display — Enable/DisableThe scanner-scale can be configured to operate with or without a Remote Display.REMOTE DIS

Product Reference Guide 1-1Section 1IntroductionThis Product Reference Guide contains comprehensive instructions on how to install the scanner or sca

6-44 Magellan® 8500 ScannerEAS Active StateSpecifies the active state polarity of EAS (Electronic Article Survellance); the inactive state is its oppo

Product Reference Guide 6-45EAS TimeoutSpecifies the amount of time that an EAS (Electronic Article Survellance) signal is held in its active state f

6-46 Magellan® 8500 ScannerAux Port ModeSelects the usage for the scanner’s optional auxiliary port. The choices listed below are mutually exclusive (

Product Reference Guide 6-47Aux Port Mode — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the scanner re

6-48 Magellan® 8500 ScannerLaser Failure ModeThis configuration item selects whether the scanner should continue oper-ating if only one laser is funct

Product Reference Guide 6-49Productivity Index Reporting (PIR)/Cashier Training (CT)When PIR/CT is enabled, label quality data is appended to decoded

6-50 Magellan® 8500 ScannerInterface Related FeaturesInterface TypeSpecifies the current scanner interface. Selections are:INTERFACE TYPEINTERFACE IDE

Product Reference Guide 6-51Interface Type — continuedTo select the desired interface:1. Disconnect current interface cable(s) if currently connected

6-52 Magellan® 8500 ScannerRS-232 Interface SelectionRemember to cover any unused bar codes on this and the facing page to ensure that the scanner rea

Product Reference Guide 6-53RS-232 Wincor-Nixdorf Interface SelectionRemember to cover any unused bar codes on this and the facing page to ensure tha

1-2 Magellan® 8500 ScannerManual OverviewSection 1, Introduction, presents the manual’s contents, describes features and specifications, provides regu

6-54 Magellan® 8500 ScannerRS-232 Single Cable Interface SelectionRemember to cover any unused bar codes on this and the facing page to ensure that th

Product Reference Guide 6-55IBM Port 17 Interface SelectionRemember to cover any unused bar codes on this and the facing page to ensure that the scan

6-56 Magellan® 8500 ScannerIBM USB Interface SelectionRemember to cover any unused bar codes on this and the facing page to ensure that the scanner re

Product Reference Guide 6-57Maximum Host-Transmitted Message LengthSpecifies the maximum number of data characters allowed in messages transmitted to

6-58 Magellan® 8500 ScannerNumber of Host Transmission BuffersSpecifies the number of host transmission(s) that may be buffered. By buffering data fro

Product Reference Guide 6-59Global PrefixThis feature applies to RS-232 interfaces (Standard, Wincor-Nixdorf, and Single Cable). It specifies the pre

6-60 Magellan® 8500 ScannerGlobal Prefix — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the scanner read

Product Reference Guide 6-61Global SuffixThis feature applies to RS-232 interfaces (Standard, Wincor-Nixdorf, and Single Cable). It specifies the suf

6-62 Magellan® 8500 ScannerGlobal Suffix — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the scanner read

Product Reference Guide 6-63IBM FeaturesIBM Interface OptionsIBM interfaces offer specific control over interaction with certain devices. Options for

Product Reference Guide 1-3How to Use This ManualYou’ll find it helpful to familiarize yourself with the first section of this manual, since it provi

6-64 Magellan® 8500 ScannerIBM Scale AddressSpecifies IBM scale address for IBM Port 17. The following three addresses are available:•6A•6B•6E To set

Product Reference Guide 6-65IBM Scale Address — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the scanne

6-66 Magellan® 8500 ScannerIBM Transmit Labels in Code 39 FormatThis feature enables/disables scanner's ability to set a symbology identifier for

Product Reference Guide 6-67IBM USB Interface OptionsThe IBM-USB interface offers specific control over interaction with cer-tain devices. Options fo

6-68 Magellan® 8500 ScannerIBM USB Interface Options — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the

Product Reference Guide 6-69IBM USB Scanner Device TypeThe IBM-USB protocol allows for the scanner to be identified as one of two different types of

6-70 Magellan® 8500 ScannerRS-232 FeaturesRS-232 Baud RateThis feature selects the baud rate required for sending and receiving data.To specify the RS

Product Reference Guide 6-71RS-232 Baud Rate — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the scanner

6-72 Magellan® 8500 ScannerRS-232 Baud Rate — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the scanner r

Product Reference Guide 6-73RS-232 Baud Rate — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the scanner

1-4 Magellan® 8500 ScannerScanner and Scanning-Scale NomenclatureControls, indicators and other nomenclature are shown in Figure 1-1.Figure 1-1. Scann

6-74 Magellan® 8500 ScannerRS-232 Number of Data BitsSpecifies number of data bits required for sending and receiving data.To set this feature:1. Scan

Product Reference Guide 6-75RS-232 Number of Stop BitsSpecifies number of stop bits required for sending and receiving data.To set this feature:1. Sc

6-76 Magellan® 8500 ScannerRS-232 ParitySpecifies parity required for sending and receiving data.Options for this setting are:• RS-232 PARITY = NONE•

Product Reference Guide 6-77RS-232 Parity — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the scanner re

6-78 Magellan® 8500 ScannerRS-232 Hardware ControlEnables/disables use of the RS-232 CTS signal for flow control and/or scan control.Options are:• Dis

Product Reference Guide 6-79RS-232 Hardware Control — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the

6-80 Magellan® 8500 ScannerRS-232 Intercharacter DelaySpecifies delay between the end of one character and the beginning of the next in 10-millisecond

Product Reference Guide 6-81RS-232 Software Flow ControlEnables/disables RS-232 Flow Control using XON/ XOFF characters. .To set this feature:1. Scan

6-82 Magellan® 8500 ScannerRS-232 Host EchoWhen enabled, this feature passes all data through the scanner to the host as it comes in. This feature is

Product Reference Guide 6-83RS-232 Host Echo Quiet IntervalThis setting specifies the time interval of RS-232 channel inactivity which must transpire

Product Reference Guide 1-5ConnectorsThe appearance of the connector panel will vary depending upon the fac-tory options purchased with your model. R

6-84 Magellan® 8500 ScannerRS-232 Ignore Host CommandsWhen set to ignore host commands, the scanner will ignore all host com-mands except for the mini

Product Reference Guide 6-85RS-232 TTLSpecifies whether RS-232 interface provides TTL levels on the output pins TxD and RTS.Choices are:• Normal RS-2

6-86 Magellan® 8500 ScannerRS-232 TTL InvertEnables/disables inversion of TTL.To set this feature:1. Scan the SWITCH bar code.2. Scan the bar code bel

Product Reference Guide 6-87RS-232 Beep on ASCII BELEnables/disables ability of scanner to beep (sound a good read tone) on receiving an ASCII BEL (0

6-88 Magellan® 8500 ScannerRS-232 Beep After WeighEnables/disables the ability of the scanner to beep after weight data is transmitted to the host. Sc

Product Reference Guide 6-89RS-232 Beep on Not on FileSelect for the host to beep (or not) when a not-on-file condition is detected by the host. This

6-90 Magellan® 8500 ScannerRS-232 ACK NAK EnableThis enables/disables the ability of the scanner to support the RS-232 ACK/NAK protocol. When configur

Product Reference Guide 6-91RS-232 ACK NAK Enable — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the sc

6-92 Magellan® 8500 ScannerRS-232 ACK CharacterThis feature specifies which ASCII character will be used as an ACK char-acter.To specify the RS-232 AC

Product Reference Guide 6-93RS-232 NAK CharacterThis feature specifies which ASCII character will be used as a NAK char-acter.To specify the RS-232 N

Datalogic Scanning, Inc.959 Terry StreetEugene, Oregon 97402Telephone: (541) 683-5700Fax: (541) 345-7140An Unpublished Work - All rights reserved. No

1-6 Magellan® 8500 ScannerPhysical ParametersThis section provides specifications for performance, environmental and electrical parameters. Reference

6-94 Magellan® 8500 ScannerRS-232 Retry on ACK NAK TimeoutThis option specifies the action scanner performs on expiration of the RS-232 ACK NAK Timeou

Product Reference Guide 6-95RS-232 ACK NAK Timeout ValueThis item specifies the time the scanner will wait for an ACK character from the host followi

6-96 Magellan® 8500 ScannerRS-232 ACK NAK Retry CountThis feature sets the number of times for the scanner to retry a label trans-mission under a retr

Product Reference Guide 6-97RS-232 ACK NAK Error HandlingThis item specifies the method the scanner will use to handle errors detected while waiting

6-98 Magellan® 8500 ScannerRS-232 ACK NAK Error Handling — continuedRemember to cover any unused bar codes on this and the facing page to ensure that

Product Reference Guide 6-99RS-232 Label ID ControlThis feature specifies whether or not Label IDs are transmitted to the host and if so, whether to

6-100 Magellan® 8500 ScannerRS-232 Label ID Control — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the s

Product Reference Guide 6-101Single Cable RS-232 OptionsThe RS-232 Single Cable interface shares some configuration options with other RS-232 interfa

6-102 Magellan® 8500 ScannerSingle Cable RS-232 Scanner Only ProtocolThis sets the type of interface protocol that will be used in Single Cable RS-232

Product Reference Guide 6-103Single Cable RS-232 RTS CTS SelectionSpecifies how RTS and CTS are used to control the data flow. RTS is con-trolled by

Product Reference Guide 1-7Automatic Zero MaintenanceThe scale’s software constantly monitors and adjusts the Zero point as long as the deviation is

6-104 Magellan® 8500 ScannerSingle Cable RS-232 RTS CTS Selection — continuedRemember to cover any unused bar codes on this and the facing page to ens

Product Reference Guide 6-105Single Cable RS-232 RTS CTS Selection — continuedRemember to cover any unused bar codes on this and the facing page to e

6-106 Magellan® 8500 ScannerSingle Cable RS-232 Use BCCEnables/disables the ability of the scanner to use BCC.To set this feature:1. Scan the SWITCH b

Product Reference Guide 6-107Single Cable RS-232 Use ACK/NAKEnables/disables the ability of the scanner to use ACK/NAK.To set this feature:1. Scan th

6-108 Magellan® 8500 ScannerSingle Cable RS-232 Use STXEnables/disables the ability of the scanner to use STX.To set this feature:1. Scan the SWITCH b

Product Reference Guide 6-109Set Single Cable RS-232 STX CharacterThis feature selects the STX character.To specify the STX Character:1. Scan the SWI

6-110 Magellan® 8500 ScannerSingle Cable RS-232 Use ETXEnables/disables the ability of the scanner to use ETX.To set this feature:1. Scan the SWITCH b

Product Reference Guide 6-111Set Single Cable RS-232 ETX CharacterAllows selection of the ETX character.To specify the ETX Character:1. Scan the SWIT

6-112 Magellan® 8500 ScannerSingle Cable RS-232 Datalogic ExtensionsWhen Datalogic1 extensions are enabled, scale calibration mode informa-tion is com

Product Reference Guide 6-113Symbology ProgrammingUPC-A EnableEnables/disables the ability of the scanner to decode UPC-A labels.To set this feature:

1-8 Magellan® 8500 ScannerFigure 1-4. Environmental SpecificationsNOTEContact technical support to learn more about this advanced programmablefeature.

6-114 Magellan® 8500 ScannerUPC-A Number System Character TransmissionEnables/disables transmission of a UPC-A number system character. To set this fe

Product Reference Guide 6-115UPC-A Check Character TransmissionEnables/disables transmission of a UPC-A check character.To set this feature:1. Scan t

6-116 Magellan® 8500 ScannerExpand UPC-A to EAN-13Enables/disables expansion of UPC-A labels to EAN/JAN-13.To set this feature:1. Scan the SWITCH bar

Product Reference Guide 6-117UPC/EAN AIM IDThis feature enables/disables transmission of the UPC/EAN AIM symbol-ogy identifier.To set this feature:1.

6-118 Magellan® 8500 ScannerUPC-A Label IDThis feature specifies a UPC-A label ID to be added to bar code data.To set this feature:1. Scan the SWITCH

Product Reference Guide 6-119UPC-A 2-Digit Supplemental Label IDThis feature specifies a UPC-A 2-Digit Supplemental label ID to be added to bar code

6-120 Magellan® 8500 ScannerUPC-A 5-Digit Supplemental Label IDThis feature specifies a UPC-A 5-Digit Supplemental label ID to be added to bar code da

Product Reference Guide 6-121UPC-A 128 Supplemental Label IDThis feature specifies a UPC-A 128 Supplemental label ID to be added to bar code data.To

6-122 Magellan® 8500 ScannerUPC-E EnableEnables/disables the ability of the scanner to decode UPC-E labels.To set this feature:1. Scan the SWITCH bar

Product Reference Guide 6-123UPC-E Number System Character TransmissionEnables/disables transmission of a UPC-E number system character.To set this f

Product Reference Guide 1-9Electrical SpecificationsBefore installation, always verify that the site’s electrical service meets the scanning-scale’s

6-124 Magellan® 8500 ScannerUPC-E Check Character TransmissionEnables/disables transmission of a UPC-E check character.To set this feature:1. Scan the

Product Reference Guide 6-125Expand UPC-E to UPC-AEnables/disables expansion of UPC-E labels to UPC-A.To set this feature:1. Scan the SWITCH bar code

6-126 Magellan® 8500 ScannerExpand UPC-E to EAN-13Enables/disables expansion of UPC-E labels to EAN/JAN-13.To set this feature:1. Scan the SWITCH bar

Product Reference Guide 6-127UPC-E Label IDThis feature specifies a UPC-E label ID to be added to bar code data.To set this feature:1. Scan the SWITC

6-128 Magellan® 8500 ScannerUPC-E 2-Digit Supplemental Label IDThis feature specifies a UPC-E 2-Digit Supplemental label ID to be added to bar code da

Product Reference Guide 6-129UPC-E 5-Digit Supplemental Label IDThis feature specifies a UPC-E 5-Digit Supplemental label ID to be added to bar code

6-130 Magellan® 8500 ScannerUPC-E 128 Supplemental Label IDThis feature specifies a UPC-E 128 Supplemental label ID to be added to bar code data.To se

Product Reference Guide 6-131EAN-13 EnableEnables/disables the ability of the scanner to decode EAN/JAN-13 labels.To set this feature:1. Scan the SWI

6-132 Magellan® 8500 ScannerEAN-13 First Character TransmissionEnables/disables transmission of EAN/JAN-13 first character.To set this feature:1. Scan

Product Reference Guide 6-133EAN-13 Check Character TransmissionEnables/disables transmission of an EAN/JAN-13 check character.To set this feature:1.

1-10 Magellan® 8500 ScannerLaser and Product SafetyLaser safety requirements are based on IEC Standard Publication 60825-1 (2001) and CDRH 21CFR, Chap

6-134 Magellan® 8500 ScannerEAN-13 ISBN Conversion EnableEnables/disables conversion of EAN/JAN-13 labels starting with 978 to Bookland ISBN labels.To

Product Reference Guide 6-135EAN 13 Label IDThis feature specifies an EAN 13 label ID to be added to bar code data.To set this feature:To set this fe

6-136 Magellan® 8500 ScannerEAN-13 2-Digit Supplemental Label IDThis feature specifies an EAN-13 2-Digit Supplemental label ID to be added to bar code

Product Reference Guide 6-137EAN-13 5-Digit Supplemental Label IDThis feature specifies an EAN-13 5-Digit Supplemental label ID to be added to bar co

6-138 Magellan® 8500 ScannerEAN-13 128 Supplemental Label IDThis feature specifies an EAN-13 128 Supplemental label ID to be added to bar code data.To

Product Reference Guide 6-139Bookland AIM IDThis feature enables/disables transmission of the Bookland AIM symbol-ogy identifier.To set this feature:

6-140 Magellan® 8500 ScannerBookland Label IDThis feature specifies a Bookland label ID to be added to bar code data.To set this feature:1. Scan the S

Product Reference Guide 6-141EAN-8 EnableEnables/disables the ability of the scanner to decode EAN/JAN-8 labels.To set this feature:1. Scan the SWITC

6-142 Magellan® 8500 ScannerEAN-8 Check Character TransmissionEnables/disables transmission of an EAN/JAN-8 check character.To set this feature:1. Sca

Product Reference Guide 6-143Expand EAN-8 to EAN-13Enables/disables expansion of EAN/JAN-8 labels to EAN/JAN-13.To set this feature:1. Scan the SWITC

Product Reference Guide 1-11Safety precautions to be taken:This Class A digital apparatus meets all requirements of the Canadian Interference-Causing

6-144 Magellan® 8500 ScannerEAN 8 Label IDThis feature specifies an EAN 8 label ID to be added to bar code data.To set this feature:To set this featur

Product Reference Guide 6-145EAN-8 2-Digit Supplemental Label IDThis feature specifies an EAN-8 2-Digit Supplemental label ID to be added to bar code

6-146 Magellan® 8500 ScannerEAN-8 5-Digit Supplemental Label IDThis feature specifies an EAN-8 5-Digit Supplemental label ID to be added to bar code d

Product Reference Guide 6-147EAN-8 128 Supplemental Label IDThis feature specifies an EAN-8 128 Supplemental label ID to be added to bar code data.To

6-148 Magellan® 8500 ScannerEAN-8 Decoding LevelsDecoding levels allow the decoder to be set to perform at one of four selectable levels:• Very Conser

Product Reference Guide 6-149EAN-8 Decoding Levels — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the s

6-150 Magellan® 8500 ScannerEAN-8 Decoding Levels — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the sca

Product Reference Guide 6-151Other UPC/EAN OptionsThe following pages contain other selectable features for UPC/EAN sym-bologies:• UPC/EAN Reconstruc

6-152 Magellan® 8500 ScannerUPC/EAN ReconstructionEnables/disables the ability of the scanner to decode a class of UPC/EAN labels with voids. The labe

Product Reference Guide 6-153Price Weight CheckEnables/disables calculation and verification of price/weight check digits. Applies to all UPC-A and E

1-12 Magellan® 8500 ScannerLabelingRegulatory, reference and safety labeling is shown in Figure 1-5.Figure 1-5. LabelingN= maxMax Min e = Max Min e =

6-154 Magellan® 8500 ScannerPrice Weight Check — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the scanne

Product Reference Guide 6-155Price Weight Check — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the scan

6-156 Magellan® 8500 ScannerEnable EAN Two LabelEnables/disables the ability of the scanner to decode EAN two-label pairs.To set this feature:1. Scan

Product Reference Guide 6-157AddonsThe scanner is capable of processing different types of addon codes, including:• 2-Digit Supplemental• 5-Digit Sup

6-158 Magellan® 8500 ScannerAddons — continuedRemember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only

Product Reference Guide 6-159UPC-A and EAN-13 Decoding LevelsDecoding levels allow the decoder to be set to perform at one of four selectable levels:

6-160 Magellan® 8500 ScannerUPC-A and EAN-13 Decoding Levels — continuedRemember to cover any unused bar codes on this and the facing page to ensure t

Product Reference Guide 6-161UPC-A and EAN-13 Decoding Levels — continuedRemember to cover any unused bar codes on this and the facing page to ensure

6-162 Magellan® 8500 ScannerGTIN EnableEnables/Disables the ability to convert UPCE, UPCA, EAN8, and EAN13 labels into the GTIN 14-character format.To

Product Reference Guide 6-163GTIN Label IDThis feature specifies a GTIN label ID to be added to bar code data when GTIN conversion is enabled.To set

Product Reference Guide 1-13Agency CompliancesThe scanner and scanning-scale meets or exceeds the requirements for its device type as set forth by th

6-164 Magellan® 8500 ScannerGTIN 2-Digit Supplemental Label IDThis feature specifies a GTIN label ID to be added to bar code data when GTIN conversion

Product Reference Guide 6-165GTIN 5-Digit Supplemental Label IDThis feature specifies a GTIN label ID to be added to bar code data when GTIN conversi

6-166 Magellan® 8500 ScannerGTIN Code 128 Supplemental Label IDThis feature specifies a GTIN label ID to be added to bar code data when GTIN conversio

Product Reference Guide 6-167RSS-14 EnableEnables/disables the ability of the scanner to decode RSS-14 labels.To set this feature:1. Scan the SWITCH

6-168 Magellan® 8500 ScannerRSS-14 Check Character TransmissionEnables/disables transmission of the RSS-14 check character.To set this feature:1. Scan

Product Reference Guide 6-169RSS-14/EAN-128 EmulationEnables/disables the ability of RSS-14 to be transmitted as EAN-128.To set this feature:1. Scan

6-170 Magellan® 8500 ScannerRSS-14 2D Component EnableWhen this feature is enabled, the software will not decode an RSS-14 bar code with a 2D componen

Product Reference Guide 6-171RSS-14 AIM IDThis feature enables/disables transmission of the RSS-14 AIM symbology identifier.To set this feature:1. Sc

6-172 Magellan® 8500 ScannerRSS-14 Label IDThis feature specifies an RSS-14 label ID to be added to bar code data.To set this feature:To set this feat

Product Reference Guide 6-173RSS Expanded EnableEnables/disables the ability of the scanner to decode RSS-Expanded labels.To set this feature:1. Scan

1-14 Magellan® 8500 ScannerBar Codes SupportedThe scanner can read/decode the following bar code types (symbologies):• UPC Versions A & E• UPC Sup

6-174 Magellan® 8500 ScannerRSS Expanded EAN-128 EmulationEnables/disables EAN 128 emulation for RSS Expanded.To set this feature:1. Scan the SWITCH b

Product Reference Guide 6-175RSS Expanded 2D Component EnableWhen this feature is enabled, the software will not decode an RSS Expanded bar code with

6-176 Magellan® 8500 ScannerRSS Expanded AIM IDThis feature enables/disables transmission of the RSS Expanded AIM symbology identifier.To set this fea

Product Reference Guide 6-177RSS Expanded Label IDThis feature specifies an RSS Expanded label ID to be added to bar code data.To set this feature:1.

6-178 Magellan® 8500 ScannerRSS Expanded Length ControlThis feature specifies either variable-length or fixed-length decoding for RSS Expanded.To set

Product Reference Guide 6-179RSS Expanded Maximum Label LengthThis feature specifies the maximum allowable length of an RSS Expanded label.To set thi

6-180 Magellan® 8500 ScannerRSS Expanded Minimum Label LengthThis feature specifies the minimum allowable length of an RSS Expanded label.To set this

Product Reference Guide 6-181RSS Expanded Fixed Length 1This feature specifies RSS Expanded first fixed length.To set this feature:1. Scan the SWITCH

6-182 Magellan® 8500 ScannerRSS Expanded Fixed Length 2This feature specifies RSS Expanded second fixed length.To set this feature:1. Scan the SWITCH

Product Reference Guide 6-183Code 39 EnableEnables/disables the ability of the scanner to decode Code 39 labels.To set this feature:1. Scan the SWITC

Product Reference Guide 2-1Section 2Site Preparation and InstallationThis section provides a reference for preparing most checkstands to receive the

6-184 Magellan® 8500 ScannerCode 39 Start Stop Character TransmissionEnables/disables transmission of Code 39 start and stop characters.To set this fe

Product Reference Guide 6-185Code 39 Check Character CalculationEnables/disables calculation and verification of an optional Code 39 check character.

6-186 Magellan® 8500 ScannerCode 39 Check Character TransmissionEnables/disables transmission of optional Code 39 check character.To set this feature:

Product Reference Guide 6-187Code 39 Full ASCIIEnables/disables the ability of the scanner to translate to Code 39 full ASCII labels.To set this feat

6-188 Magellan® 8500 ScannerCode 39 AIM IDThis feature enables/disables transmission of the Code 39 AIM symbology identifier.To set this feature:1. Sc

Product Reference Guide 6-189Code 39 Label IDThis feature specifies a Code 39 label ID to be added to bar code data.To set this feature:1. Scan the S

6-190 Magellan® 8500 ScannerCode 39 Length ControlThis feature specifies whether variable-length or fixed-length decoding will be set for Code 39.To s

Product Reference Guide 6-191Code 39 Maximum Label LengthThis feature specifies the maximum allowable length of a Code 39 label.To set this feature:1

6-192 Magellan® 8500 ScannerCode 39 Minimum Label LengthThis feature specifies the minimum allowable length of a Code 39 label.To set this feature:1.

Product Reference Guide 6-193Code 39 Fixed Length 1This feature specifies Code 39 first fixed length.To set this feature:1. Scan the SWITCH bar code.

Product Reference Guide 1TABLE OF CONTENTSSection 1. Introduction...

2-2 Magellan® 8500 ScannerFigure 2-1. The Scanner/Scale FamilyPre-Installation ConsiderationsIt should be noted that the scope of this manual does not

6-194 Magellan® 8500 ScannerCode 39 Fixed Length 2This feature specifies Code 39 second fixed length.To set this feature:1. Scan the SWITCH bar code.2

Product Reference Guide 6-195Code 39 StitchingEnables/disables stitching for Code 39 labels. When parts of a Code 39 bar code are presented to the sc

6-196 Magellan® 8500 ScannerPharmacode 39 EnableEnables/disables the ability of the scanner to decode Italian Pharmacode 39 labels.To set this feature

Product Reference Guide 6-197Pharmacode 39 Start Stop Character TransmissionEnables/ disables transmission of start and stop characters for Pharmacod

6-198 Magellan® 8500 ScannerPharmacode 39 Check Character TransmissionEnables/disables transmission of Pharmacode 39 check character.To set this featu

Product Reference Guide 6-199Pharmacode 39 Label IDThis feature specifies a Pharmacode 39 label ID to be added to bar code data.To set this feature:1

6-200 Magellan® 8500 ScannerCode 128 EnableEnables/disables the ability of the scanner to decode Code 128 labels.To set this feature:1. Scan the SWITC

Product Reference Guide 6-201Code 128 Transmit Function CharactersEnables/disables transmission of Code 128 function characters 1, 2, 3, and 4.To set

6-202 Magellan® 8500 ScannerConvert Code128 to Code 39Enables/disables conversion of Code 128 labels to Code 39.To set this feature:1. Scan the SWITCH

Product Reference Guide 6-203Code 128 AIM IDThis feature enables/disables transmission of the Code 128 AIM symbol-ogy identifier.To set this feature:

Product Reference Guide 2-3Checkstand Design1. Select a design which allows load-sharing by several muscle groups (for example designs which allow th

6-204 Magellan® 8500 ScannerCode 128 Label IDThis feature specifies a Code 128 label ID to be added to bar code data..To set this feature:1. Scan the

Product Reference Guide 6-205Code 128 Length ControlThis feature specifies whether variable-length or fixed-length decoding will be set for Code 128.

6-206 Magellan® 8500 ScannerCode 128 Maximum Label LengthThis feature specifies the maximum allowable length of a Code 128 label.To set this feature:1

Product Reference Guide 6-207Code 128 Minimum Label LengthThis feature specifies the minimum allowable length of a Code 128 label.To set this feature

6-208 Magellan® 8500 ScannerCode 128 Fixed Length 1This feature specifies Code 128 first fixed length.To set this feature:1. Scan the SWITCH bar code.

Product Reference Guide 6-209Code 128 Fixed Length 2This feature specifies Code 128 second fixed length.To set this feature:1. Scan the SWITCH bar co

6-210 Magellan® 8500 ScannerCode 128 StitchingEnables/disables stitching for Code 128 labels. When parts of a Code 128 bar code are presented to the s

Product Reference Guide 6-211EAN-128 EnableEnables/disables the ability of the scanner to decode EAN-128 labels.To set this feature:1. Scan the SWITC

6-212 Magellan® 8500 ScannerEAN 128 AIM IDThis feature enables/disables transmission of the EAN 128 AIM symbol-ogy identifier.To set this feature:1. S

Product Reference Guide 6-213EAN 128 Label IDThis feature specifies an EAN 128 label ID to be added to bar code data..To set this feature:1. Scan the

2-4 Magellan® 8500 ScannerScanner Installation1. Mount the horizontal surface of the scanner flush with the coun-tertop to encourage slide scanning ra

6-214 Magellan® 8500 ScannerInterleaved 2 of 5 (I 2 OF 5) EnableEnables/disables the ability of the scanner to decode Interleaved 2 of 5 labels.To set

Product Reference Guide 6-215I 2 of 5 Check Character CalculationEnables/disables calculation and verification of an optional Interleaved 2 of 5 chec

6-216 Magellan® 8500 ScannerI 2 of 5 Check Character TransmissionEnables/disables transmission of an optional Interleaved 2 of 5 check char-acter.To s

Product Reference Guide 6-217I 2 of 5 AIM IDThis feature enables/disables transmission of the I 2 of 5 AIM symbology identifier.To set this feature:1

6-218 Magellan® 8500 ScannerI 2 of 5 Label IDThis feature specifies an I 2 of 5 label ID to be added to bar code data..To set this feature:1. Scan the

Product Reference Guide 6-219I 2 of 5 Length ControlThis feature specifies whether variable-length or fixed-length decoding will be set for I 2 of 5.

6-220 Magellan® 8500 ScannerI 2 of 5 Maximum Label LengthThis feature specifies the maximum allowable length of an I 2 of 5 label.To set this feature:

Product Reference Guide 6-221I 2 of 5 Minimum Label LengthThis feature specifies the minimum allowable length of an I 2 of 5 label.To set this featur

6-222 Magellan® 8500 ScannerI 2 of 5 Fixed Length 1This feature specifies I 2 of 5 first fixed length.To set this feature:1. Scan the SWITCH bar code.

Product Reference Guide 6-223I 2 of 5 Fixed Length 2This feature specifies I 2 of 5 second fixed length.To set this feature:1. Scan the SWITCH bar co

Product Reference Guide 2-5Since the scanner reads labels on all four sides plus the top and bottom, there is no need to turn a bar code toward eithe

6-224 Magellan® 8500 ScannerI 2 of 5 StitchingEnables/disables stitching for I 2 of 5 labels. When parts of an I 2 of 5 bar code are presented to the

Product Reference Guide 6-225Codabar EnableEnables/disables the ability of the scanner to decode Codabar labels.To set this feature:1. Scan the SWITC

6-226 Magellan® 8500 ScannerCodabar Start Stop Character TransmissionEnables/disables transmission of Codabar start and stop characters.To set this fe

Product Reference Guide 6-227Codabar Start Stop Character SetThis feature selects the format of transmitted Codabar start/stop charac-ters.Options ar

6-228 Magellan® 8500 ScannerCodabar Start Stop Character Set — continuedRemember to cover any unused bar codes on this and the facing page to ensure t

Product Reference Guide 6-229Codabar Start Stop Character MatchEnables/disables the requirement that start and stop characters match.To set this feat

6-230 Magellan® 8500 ScannerCodabar Check Character CalculationEnables/disables calculation and verification of an optional Codabar check character.To

Product Reference Guide 6-231Codabar Check Character TransmissionEnables/disables transmission of an optional Codabar check character.To set this fea

6-232 Magellan® 8500 ScannerCodabar AIM IDThis feature enables/disables transmission of the Codabar AIM symbology identifier.To set this feature:1. Sc

Product Reference Guide 6-233Codabar Label IDThis feature specifies a Codabar label ID to e added to bar code data.To set this feature:1. Scan the SW

2-6 Magellan® 8500 ScannerCounter Preparation. Since the majority of grocery checkout lanes are designed as “left-hand take away,” the counter drawing

6-234 Magellan® 8500 ScannerCodabar Length ControlThis feature specifies whether variable-length or fixed-length decoding will be set for Codabar.To s

Product Reference Guide 6-235Codabar Maximum Label LengthThis feature specifies the maximum allowable length of a Codabar label.To set this feature:1

6-236 Magellan® 8500 ScannerCodabar Minimum Label LengthThis feature specifies the minimum allowable length of a Codabar label.To set this feature:1.

Product Reference Guide 6-237Codabar Fixed Length 1This feature specifies Codabar first fixed length.To set this feature:1. Scan the SWITCH bar code.

6-238 Magellan® 8500 ScannerCodabar Fixed Length 2This feature specifies Codabar second fixed length.To set this feature:1. Scan the SWITCH bar code.2

Product Reference Guide 6-239Codabar StitchingEnables/disables stitching for Codabar labels. When parts of a Codabar bar code are presented to the sc

6-240 Magellan® 8500 ScannerCode 93 EnableEnables/disables the ability of the scanner to decode Code 93 labels.To set this feature:1. Scan the SWITCH

Product Reference Guide 6-241Code 93 AIM IDThis feature enables/disables transmission of the Code 93 AIM symbology identifier.To set this feature:1.

6-242 Magellan® 8500 ScannerCode 93 Label IDThis feature specifies a Code 93 label ID to be added to bar code data..To set this feature:1. Scan the SW

Product Reference Guide 6-243Code 93 Length ControlThis feature specifies whether variable-length or fixed-length decoding will be set for Code 93.To

Product Reference Guide 2-7Figure 2-2. Vertical ClearanceVentilation and SpacingThe scanning-scale’s perimeter housing has been designed to provide a

6-244 Magellan® 8500 ScannerCode 93 Maximum Label LengthThis feature specifies the maximum allowable length of a Code 93 label.To set this feature:1.

Product Reference Guide 6-245Code 93 Minimum Label LengthThis feature specifies the minimum allowable length of a Code 93 label.To set this feature:1

6-246 Magellan® 8500 ScannerCode 93 Fixed Length 1This feature specifies Code 93 first fixed length.To set this feature:1. Scan the SWITCH bar code.2.

Product Reference Guide 6-247Code 93 Fixed Length 2This feature specifies Code 93 second fixed length.To set this feature:1. Scan the SWITCH bar code

6-248 Magellan® 8500 ScannerCode 93 StitchingEnables/disables stitching for Code 93 labels. When parts of a Code 93 bar code are presented to the scan

Product Reference Guide 6-249MSI/Plessey EnableEnables/disables the ability of the scanner to decode MSI/Plessey labels.To set this feature:1. Scan t

6-250 Magellan® 8500 ScannerMSI/Plessey Check Character CalculationEnables/disables calculation and verification of optional MSI/Plessey check charact

Product Reference Guide 6-251MSI/Plessey Number of Check CharactersSpecifies number of MSI/Plessey check characters to be calculated and verified.To

6-252 Magellan® 8500 ScannerMSI/Plessey Check Character TransmissionEnables/disables transmission of optional MSI/Plessey check characters.To set this

Product Reference Guide 6-253MSI/Plessey AIM IDThis feature enables/disables transmission of the MSI/Plessey AIM sym-bology identifier.To set this fe

2-8 Magellan® 8500 ScannerFigure 2-3. Debris Chutes & Ventilation SlotsService AccessThe scanner and scanning-scale have been engineered to allow

6-254 Magellan® 8500 ScannerMSI/Plessey Label IDThis feature specifies an MSI/Plessey label ID to be added to bar code data.To set this feature:1. Sca

Product Reference Guide 6-255MSI/Plessey Length ControlThis feature specifies whether variable-length or fixed-length decoding will be set for MSI/Pl

6-256 Magellan® 8500 ScannerMSI/Plessey Maximum Label LengthThis feature specifies the maximum allowable length of an MSI/Plessey label.To set this fe

Product Reference Guide 6-257MSI/Plessey Minimum Label LengthThis feature specifies the minimum allowable length of an MSI/Plessey label.To set this

6-258 Magellan® 8500 ScannerMSI/Plessey Fixed Length 1This feature specifies MSI/Plessey first fixed length.To set this feature:1. Scan the SWITCH bar

Product Reference Guide 6-259MSI/Plessey Fixed Length 2This feature specifies MSI/Plessey second fixed length.To set this feature:1. Scan the SWITCH

6-260 Magellan® 8500 ScannerMSI/Plessey StitchingEnables/disables stitching for MSI/Plessey labels. When parts of an MSI/Plessey bar code are presente

Product Reference Guide 6-261Standard 2 of 5 EnableEnables/disables the ability of the scanner to decode Standard 2 of 5 labels.To set this feature:1

6-262 Magellan® 8500 ScannerStandard 2 of 5 Check Character CalculationEnables/disables calculation and verification of an optional Standard 2 of 5 ch

Product Reference Guide 6-263Standard 2 of 5 Check Character TransmissionEnables/disables transmission of an optional Standard 2 of 5 check charac-te

Product Reference Guide 2-9Power InstallationReference the wiring diagram in Figure 2-4 for the recommended fusing arrangement.GroundingThe AC/DC Pow

6-264 Magellan® 8500 ScannerStandard 2 of 5 AIM IDThis feature enables/disables transmission of the Standard 2 of 5 AIM symbology identifier.To set th

Product Reference Guide 6-265Standard 2 of 5 Label IDThis feature specifies an Standard 2 of 5 label ID to be added to bar code data.To set this feat

6-266 Magellan® 8500 ScannerStandard 2 of 5 Length ControlThis feature specifies whether variable-length or fixed-length decoding will be set for Stan

Product Reference Guide 6-267Standard 2 of 5 Maximum Label LengthThis feature specifies the maximum allowable length of a Standard 2 of 5 label.To se

6-268 Magellan® 8500 ScannerStandard 2 of 5 Minimum Label LengthThis feature specifies the minimum allowable length of an Standard 2 of 5 label.To set

Product Reference Guide 6-269Standard 2 of 5 Fixed Length 1This feature specifies Standard 2 of 5 first fixed length.To set this feature:1. Scan the

6-270 Magellan® 8500 ScannerStandard 2 of 5 Fixed Length 2This feature specifies Standard 2 of 5 second fixed length.To set this feature:1. Scan the S

Product Reference Guide 6-271Standard 2 of 5 StitchingEnables/disables stitching for Standard 2 of 5 labels. When parts of a Stan-dard 2 of 5 bar cod

6-272 Magellan® 8500 ScannerNOTES

Product Reference Guide A-1Appendix ALED/Beeper Indications & ControlsFigure A-1 shows the operator’s controls and indicators. The descriptions f

2-10 Magellan® 8500 ScannerCheckstand PreparationReference Figure 2-5. When performing a first time installation into a new checkstand, verify before

A-2 Magellan® 8500 ScannerIndicator LEDsThe green LED indicates scanner status, and the yellow LED is primarily used to show scale status as described

Product Reference Guide A-3Volume/Tone Push ButtonThe Volume/Tone Push Button also performs multiple functions depend-ing upon the duration of time i

A-4 Magellan® 8500 ScannerTable A-2. Volume/Tone Push Button FunctionsPRESSDURATIONFUNCTION COMMENTMomentary (when scanner is asleep)Wakes scanner fro

Product Reference Guide A-5Scale Zero Push ButtonThe Scale Zero Push Button is used for multiple functions as listed in Table A-3.Table A-3. Scale Ze

A-6 Magellan® 8500 ScannerCalibration Switch CoverThis cover restricts access to the Calibration Switch to help guard against unauthorized tampering w

Product Reference Guide B-1Appendix BCable InformationIntroductionThe following pages contain pinout information, enabling you to create standard int

B-2 Magellan® 8500 ScannerRS-232 Cable PinoutScannerConnector HardwareRJ45, 10 PositionCable PinoutTable B-1. RS-232 Cable PinoutsPIN # FUNCTION DESCR

Product Reference Guide B-3RS-232 Cable Pinout — continuedScaleConnector HardwareRJ45, 10 PositionCable PinoutTable B-2. PIN # FUNCTION DESCRIPTION1

B-4 Magellan® 8500 ScannerIBM Cable PinoutScanner and ScaleConnector HardwareRJ45, 10 PositionCable PinoutTable B-3PIN # FUNCTION DESCRIPTION1 +5V pul

Product Reference Guide B-5IBM USB Cable PinoutScanner and ScaleConnector HardwareRJ45, 10 PositionCable PinoutTable B-4PIN # FUNCTION DESCRIPTION1 +

Product Reference Guide 2-11Liquid Spills and Moisture Select a checkstand design which allows fluids to flow through, and directs liquids away from

B-6 Magellan® 8500 ScannerAuxiliary PortExternal Handheld InputConnector HardwareRJ45, 10 PositionCable PinoutTable B-5PIN # FUNCTION DESCRIPTION1 +5V

Product Reference Guide B-7EAS Interlock ConnectorScanner and ScaleConnector HardwareRJ-4Cable PinoutNOTEAntenna Connections. Connect ONLY using appr

B-8 Magellan® 8500 ScannerNOTES

Product Reference Guide C-1Appendix CKeypadUse the bar codes in this section to enter numbers and characters as you would select digits/characters fr

C-2 Magellan® 8500 ScannerUse the bar codes in this section to enter numbers and characters as you would select digits/characters from a keypad.Scan y

Product Reference Guide C-3Use the bar codes in this section to enter numbers and characters as you would select digits/characters from a keypad.Scan

C-4 Magellan® 8500 ScannerUse the bar codes in this section to enter numbers and characters as you would select digits/characters from a keypad.Scan y

Product Reference Guide C-5Use the bar codes in this section to enter numbers and characters as you would select digits/characters from a keypad.Scan

C-6 Magellan® 8500 ScannerUse the bar codes in this section to enter numbers and characters as you would select digits/characters from a keypad.Scan y

Product Reference Guide C-7Use the bar codes in this section to enter numbers and characters as you would select digits/characters from a keypad.Scan

2 Magellan® 8500 ScannerGrounding ...2-

2-12 Magellan® 8500 ScannerInterface cables (and display cable, if applicable) should be routed away from all highly inductive electrical devices, lik

C-8 Magellan® 8500 ScannerUse the bar codes in this section to enter numbers and characters as you would select digits/characters from a keypad.Scan y

Product Reference Guide D-1Appendix DHost CommandsAccepting Commands from an RS-232 Scan-ner HostThe scanner responds to the following RS-232 command

D-2 Magellan® 8500 ScannerNOTES

Product Reference Guide E-1Appendix EFactory DefaultsThe following table provides a listing of the most common factory settings for the interfaces sh

E-2 Magellan® 8500 ScannerScale Enforced Zero Return0 (disable) 0 (disable) 0 (disable) 0 (disable) 0 (disable) 0 (disable)Scale Interface Type4 (RS-2

Product Reference Guide E-3IBM USB Scanner Device Type0 (fixed scanner)RS-232 Baud Rate 1 (9600) 1 (9600) 1 (9600) 1 (9600)RS-232 Number of Data Bits

E-4 Magellan® 8500 ScannerRS-232 ACK NAK Enable0 (disable) 0 (disable) 0 (disable)RS-232 ACK Character 6 (ACK) 6 (ACK) 6 (ACK)RS-232 NAK Character 21

Product Reference Guide E-5Single Cable RS-232 Datalogic Extensions0 (stdprotocol)UPC-A Enable 1 (enable) 1 (enable) 1 (enable) 1 (enable) 1 (enable)

E-6 Magellan® 8500 ScannerUPC-E 2-Digit Supple-mental Label ID4500("E") 4500("E") 4300("C") 4500("E")UPC-E 5-D

Product Reference Guide E-7EAN-8 2-Digit Supple-mental Label ID4646 ("FF")4646 ("FF")4200 ("B")4646 ("FF")EAN

Product Reference Guide 2-13Figure 2-6. Typical Checkstand Design & Cutout LocationOptionalItem DiverterConveyorDeadplateScannerBaggingAreaTake-A

E-8 Magellan® 8500 ScannerRSS Expanded Label ID5258 ("RX")5258 ("RX")4500 ("E")5258 ("RX")RSS Expanded Length

Product Reference Guide E-9Code 39 Fixed Length 1 888888Code 39 Fixed Length 2 14 14 14 14 14 14Code 39 Stitching 1 (enable) 1 (enable) 1 (enable) 1

E-10 Magellan® 8500 ScannerCode 128 Stitching 1 (enable) 1 (enable) 1 (enable) 1 (enable) 1 (enable) 1 (enable)EAN-128 Enable 0 (disable) 0 (disable)

Product Reference Guide E-11Codabar Start Stop Character Match0 (disable) 0 (disable) 0 (disable) 0 (disable) 0 (disable) 0 (disable)Codabar Check Ch

E-12 Magellan® 8500 ScannerCode 93 Stitching 1 (enable) 1 (enable) 1 (enable) 1 (enable) 1 (enable) 1 (enable)MSI/Plessey Enable 0 (disable) 0 (disabl

Product Reference Guide E-13Standard 2 of 5 Label ID5300 ("S") 5300 ("S") 5300 ("S") 5300 ("S") 5300 ("S

E-14 Magellan® 8500 ScannerNOTES

Product Reference Guide F-1Appendix FHandheld Data Format RequirementsThis appendix provides application notes to describe the general format of data

F-2 Magellan® 8500 ScannerDatalogic Handheld Data Format RequirementsThe following sections describe label transmission formats that are typi-cally ob

Product Reference Guide F-3UPC-A with 5-Digit Supplemental• Number system must be included in label data• Check digit must be included in label data

2-14 Magellan® 8500 ScannerRefer to the appropriate drawing (Figure 2-7, Model 8500; Figure 2-8, Models 8501 and 8502) for dimensional information on

F-4 Magellan® 8500 ScannerUPC-E with 2-Digit Supplemental• Number system must be included in label data.• Check digit must be included in label data a

Product Reference Guide F-5EAN-8• Check digit must be included in label data and is assumed to be correct• Prefix must be an ASCII characters 'F

F-6 Magellan® 8500 ScannerEAN-13• Check digit must be included in label data and is assumed to be correct• Prefix must be an ASCII character 'F&a

Product Reference Guide F-7Code 39• Check character must be included in label data.• Label length including start, stop and check characters and excl

F-8 Magellan® 8500 ScannerCodabar• Check character must be included in label data.• Label length including check character and excluding prefix char-a

Product Reference Guide F-9MSI/Plessey• Check character must be included in label data.• Label length including check character and excluding prefix

F-10 Magellan® 8500 ScannerAIM FormatsAIM specifies a 3-character string that is attached as a prefix to the label data for transmission. Because AIM

Product Reference Guide F-112-Digit Supplemental• Supplemental data is appended to any EAN base label.• Prefix must be ASCII characters ']E1&apo

F-12 Magellan® 8500 ScannerCode 128 Supplemental• Supplemental data is appended to any EAN base label.• Prefix must be ASCII characters ']C0&apos

Product Reference Guide F-13Codabar• Check character must be included in label data.• Label length including check character and excluding prefix cha

Product Reference Guide 2-15Figure 2-8. Models 8501 and 8502 Long Scanner or Scanning-Scale Cutout DimensionsModel 8501& Model 8502DimensionsMode

F-14 Magellan® 8500 ScannerRSS Expanded• Prefix must be ASCII characters ']e0'.• Label length excluding prefix characters must be at least 1

Product Reference Guide F-15PDF417• Prefix must be an ASCII characters ']L0'.• Label length excluding prefix character cannot exceed 300 ch

F-16 Magellan® 8500 ScannerNOTES

Product Reference Guide F-17NOTES

F-18 Magellan® 8500 ScannerNOTES

ASCII Character SetThe table on this page shows a set of ASCII characters and their corresponding Hex Values. The Hex Values in this table are needed

AustraliaDatalogic Scanning Pty LtdNorth Ryde, AustraliaTelephone: [61] (2) 9870 3200Fax: [61] (2) 9878 8688France and BeneluxDatalogic Scanning Sarl

2-16 Magellan® 8500 ScannerCheckstand MountingThere are a number of things to take into account when installing the unit into a checkstand. Key factor

Product Reference Guide 2-17• Lift out the accessory box containing the AC/DC Power Supply, optional Remote Scale Display and cable (if present), and

2-18 Magellan® 8500 ScannerOperational VerificationFollow these steps to ensure that your unit has arrived undamaged and is fully functional before in

Product Reference Guide 2-194. Verify that the scanner or scanning-scale passes an operational test by observing the following:Scanner. Pass UPC/EAN

2-20 Magellan® 8500 ScannerDiagnostic ModesTwo diagnostic modes are available which allow you to initiate scanner or scale diagnostic tests, as well a

Product Reference Guide 2-21Scale Diagnostic ModeTo enter Scale Diagnostic Mode, press the Scale Zero Push Button for approximately four seconds. Six

Product Reference Guide 3Programming ... 3-

2-22 Magellan® 8500 ScannerFigure 2-10. Cable RoutingScannerAC PowerSwitch(recommended)AC/DCPowerSupplyScannerInterface CableScaleInterface Cable(Scan

Product Reference Guide 2-23Figure 2-11 provides physical dimensions for the AC/DC Adapter (part number 8-0599).Figure 2-11. Physical Measurements: A

2-24 Magellan® 8500 ScannerViewing AngleThe optimum viewing angle is directly facing the customer. To ensure that the display is easily readable for t

Product Reference Guide 2-25Placing and Installing the Remote Scale Display(Short Pedestal Base ONLY)1. Determine where you want to install the Remot

2-26 Magellan® 8500 ScannerFigure 2-13. Physical Measurements: Remote Display (Short Base)6. Cut the stalk to fit your installation (if required).7. R

Product Reference Guide 2-27Figure 2-14. Remote Scale Display Components.Figure 2-15. Remote Scale Short Base Display Mounting Template48 - 60"

2-28 Magellan® 8500 ScannerChanging Weighing ModesYour scanning-scale has been programmed for weighing in either pounds or kilograms depending upon th

Product Reference Guide 2-29Figure 2-16. Connecting Cables to the Scanner/ScaleFigure 2-17. Connecting the Optional EAS Interlock CablePOS TERMINAL R

2-30 Magellan® 8500 ScannerInstallation1. Make sure that all cables are firmly attached (except that the AC/DC power supply should not be connected to

Product Reference Guide 2-313. Hook the fingers of both hands into the lift handles located along the insides of the scanner walls, just above the de

4 Magellan® 8500 ScannerBlanking Test ...5-16

2-32 Magellan® 8500 ScannerFigure 2-19. Using the Lift HandlesLift Handles

Product Reference Guide 2-33System Power-Up RecapThe System Power-Up procedure may vary depending upon the require-ments of your POS system. It is ge

2-34 Magellan® 8500 ScannerNOTES

Product Reference Guide 3-1Section 3Operation and MaintenanceThe information contained in this section describes how to operate and maintain the scan

3-2 Magellan® 8500 ScannerProper Scanning TechniqueThe scanner was designed to provide the ultimate in ergonomic enhance-ments for Point-Of-Sale (POS)

Product Reference Guide 3-3Proper Weighing Technique1. The L-shaped All-Weighs™ platter allows you to place items anywhere on its surface, including

3-4 Magellan® 8500 ScannerOperational ControlsThe function of scanner and scale controls and indicators is listed in Appendix A, LED/Beeper Indication

Product Reference Guide 3-5Error ReportingIf a fatal error is detected during Selftest or operation, the unit will not advance to Normal Operation Mo

3-6 Magellan® 8500 Scanner• When the scanner or scanner/scale completes its Selftest success-fully, it emits a tone (when configured to do so) and ent

Product Reference Guide 3-7Additional FunctionsAdditional scanner and scale functions include programming, running scanner or scale diagnostics, init

Product Reference Guide 5Scale LED Enable ... 6-42Re

3-8 Magellan® 8500 ScannerScale AdjustmentsThe scale allows two user adjustments: zeroing and calibration. The first, and most frequently performed, i

Product Reference Guide 3-9Normally, once the scale has been calibrated, the calibration must be veri-fied and/or approved by a local regulatory body

3-10 Magellan® 8500 ScannerOperational MaintenanceThe scanner or scanner/scale will provide dependable service for many years. The following maintenan

Product Reference Guide 3-11Vertical Scan Window ReplacementThe Vertical Scan Window enclosed in the All Weighs™ Platter is a replaceable part. Follo

3-12 Magellan® 8500 Scanner2. If the top edge of the platter is blocked, you may find it easier to grasp the platter vertical bezel as shown in Figure

Product Reference Guide 3-134. Fully seat the new vertical scan window into the window channel within its bottom retention tabs. Tilt the window in t

3-14 Magellan® 8500 ScannerFigure 3-5. Removing/Replacing the WRG WindowSlide WRGWindow OutRemoveVertical Bezel

Product Reference Guide 4-1Section 4Problem IsolationIn the event of a suspected functional problem, use the troubleshooting references provided in t

4-2 Magellan® 8500 ScannerDiagnostic TestsSee Section 2, Diagnostic Modes, for details about running diagnostic tests for the scanner and/or scale. If

Product Reference Guide 4-3Error CodesIf an error is detected, the scanner will sound a long low tone (for three seconds) and alternately flash its L

6 Magellan® 8500 ScannerRS-232 Beep on ASCII BEL ...6-87RS-232 Beep

4-4 Magellan® 8500 ScannerTable 4-1. Error Codes and Corrective ActionError CodeProbable Cause Corrective Action0BlinkingConfigurationNo POS interface

Product Reference Guide 4-5Figure 4-1. 7-Segment LED Display7-Segment Display

4-6 Magellan® 8500 ScannerScale Error ReportingScale diagnostics uses the Remote Scale Display and the Zero Status lamp to communicate specific scale

Product Reference Guide 4-7FlowchartsThe problem isolation flowcharts on the following pages allow you to identify and troubleshoot problems with you

4-8 Magellan® 8500 ScannerFigure 4-3. Problem Isolation: SelftestCall Tech SupportCall Tech SupportError code 4. indicates a failed horizontal VLDM (l

Product Reference Guide 4-9Figure 4-4. Problem Isolation: Poor/No ReadingDONEDONEPOOR/NO READINGSTARTHave you verified thatall scan windows are clean

4-10 Magellan® 8500 ScannerFigure 4-5. Problem Isolation: No Transmit to POSDONEDONENO TRANSMIT TO POSSTARTVerify programmable parameters using the in

Product Reference Guide 4-11Figure 4-6. Problem Isolation: ScaleFor this error, the 7-segment display may also show a 'C'.SCALE STARTView t

4-12 Magellan® 8500 ScannerFigure 4-7. Problem Isolation: Remote DisplayCall Tech SupportDONEDONEREMOTE DISPLAYSTARTYESYESYESYESNONONONOIs theunit con

Product Reference Guide 5-1Section 5CalibrationA number of situations require the scale to be calibrated. They are:• at initial installation of the s

Product Reference Guide 7UPC-E 2-Digit Supplemental Label ID ... 6-128UPC-E 5-Digit S

5-2 Magellan® 8500 ScannerDescription of Calibration SequenceThe Calibration Sequence sets the scale to an accurate reference point for weighing. This

Product Reference Guide 5-3Motion TestThis test verifies that the scale will not ‘zero’ when the weighing surface of the scanner/scale is in motion.1

5-4 Magellan® 8500 ScannerAutomatic Zeroing if Scale is Under ZeroThe scanner/scale is equipped with a feature that automatically zeros the scale if i

Product Reference Guide 5-5Calibrating the Scale (Pounds & Kilograms)1. Before proceeding, ensure that the scanner/scale has been pre-pared for t

5-6 Magellan® 8500 Scannerthe Field Standard Weight set on the center of the weighing area and press the Zero Push Button again.9. The Yellow LED will

Product Reference Guide 5-7Figure 5-1. Calibration Access CoverFigure 5-2. Calibration SwitchCalibration CoverCalibration Switch

5-8 Magellan® 8500 ScannerCalibration Verification (U.S. Pounds)Once you have completed the calibration sequence, you may be required to perform these

Product Reference Guide 5-9Increasing-Load Test (Phase 1)This test checks Scale operation with five, ten and fifteen pound weights.1. Check that the

5-10 Magellan® 8500 ScannerFigure 5-3. Shift TestACBDACBD

Product Reference Guide 5-11Increasing- Load Test (Phase 2)After completing the Shift Test, you must complete the Increasing Load Test using 20.0, 25