User's manualDatalogic DLL2020-WO
c) You can also hold the scanner without the handle.126 The DLL2020-WO
1.3 Scanner labellingThere are four labels on the scanner. The first three labels can be foundon the housing of the DLL2020-WO, as indicated in the fi
Laser safetyEnglish:The DLL2020-WO scanner complies with safety standard IEC 825-1(1993) for a Class 1 laser product. It also complies with U.S. 21CFR
Finnish:DLL2020-WO-skanneri täyttää luokan 1 lasertuotteelle IEC 825-1:ssä(1993) asetetut turvavaatimukset. Se täyttää myös U.S. 21CFR1040:ssaasetetut
Optical The use of optical instruments with this product willincrease eye hazard. Optical instruments includebinoculars, microscopes and magnifying gl
1.4 Maintaining the scannerThe DLL2020-WO scanner requires little maintenance. Only occasionalcleaning of the scanner window is necessary in order to
POS system Polaris P-7010Scanner control12 The DLL2020-WODLL2020-WO
Chapter 2Installing the DLL2020-WO
14 Installing the DLL2020-WO2.1 Installing the scanner This chapter describes the instructions necessary for installing theDLL2020-WO scanner.Due to m
Installing the DLL2020-WO 152. You have four options to connect the scanner to your POS orcomputer.A) RS232 direct powerFor those systems which supply
Copyright © 1998, Datalogic. This manual is copyrighted, with all rights reserved. Under the copyright laws, this manual may not, in wholeor in part,
16 Installing the DLL2020-WOB) Keyboard Wedge direct powerFor those systems which supply electrical power on the keyboardport (minimal requirements: +
Installing the DLL2020-WO 17C) RS232 non direct powerFor those systems which do not supply electrical power on theserial port, the following set-up is
18 Installing the DLL2020-WOD) Keyboard Wedge non direct powerFor those systems which do not supply electrical power on thekeyboard port, the followin
Installing the DLL2020-WO 19OPEN PROGRAMMING MODE1.To select the scanner interface (RS232 factory default), scan thefollowing codes:1. Open the scanne
20 Installing the DLL2020-WORETURN TO RS232 DEFAULT2.IMPORTANT: Programming Mode is closed after scanning this code.RETURN TO KEYBOARD WEDGE DEFAULT3.
AppendicesA. Connector types and pin definitionsB. Technical SpecificationsC. Troubleshooting
22 AppendicesA. Connector types and pin definitionsThe Dll2020-wo has a dual interface: RS232/Keyboard Wedge. The pindefinition for the scanner port a
Appendices 23B. Technical specificationsElectrical Power supply voltage 100 - 250 V ac, 50/60 Hz DC input to scanner + 5 V dc ±5%, 250 mA
24 AppendicesC. TroubleshootingThis section contains information on solving problems you may encounterwhen using the scanner. If troubles occur, take
Appendices 25 The scanner is on but a bar code cannot be read. The LED is red.Diagnostic Tipsn The scanner window is dirty. Clean then
Table of contentsPreface iChapter 1 The DLL2020-WO 11.1 Unpacking the DLL2020-WO 21.2 Scanning bar codes with the DLL2020-WO 41.3 Scanner labelling 7
26 Appendices The green LED stays on.A bar code is read by the scanner butnot accepted by the host system.Diagnostic TipsThe scanner i
PrefaceThe Datalogic DLL2020-WO is a high performance omni-directional scanner, whichprovides optimal scanning conditions. The DLL2020-WO shares the
Chapter 1The DLL2020-WO
1.1 Unpacking the DLL2020-WO Take the scanner and its accessories out of the box and remove allpacking materials. Refer to the packing list in order t
The various parts of the DLL2020-WO are:Sleep mode switch If a sleep mode time-out has been programmed,the scanner can be reactivated by pressing this
1.2 Scanning bar codes with the DLL2020-WOThe DLL2020-WO is an omnidirectional scanner featuring a 4-directionalscan field with a 16-lines scan patter
The Dll2020-wo scanner can be used handsfree as well as hand held,e.g.:a) Handsfree scanning by presenting the item to the scanner.b) Bar code labels
Kommentare zu diesen Handbüchern